How To Make An Outboard Test Tank

Fill the barrel and youre ready to test run. It works ok for a short test and this size of motor - just to make sure the electrics are working and the.

A 1960s Outboard Motor In Original Casing Sparks Anzani British Made Sold 120 Lot 277 Auction 2 3 16 Bourneendauction Outboard Motors Outboard Water Crafts

Pinch off the fuel tank vent hose.

How to make an outboard test tank. How to Test and Outboard Motor on Land. - Rebuild Service For Yamaha outboard 60 70 75 85 90HP 3 Ram trim tilt unit 6H1-10. Install the inflatable pipe plug into the fuel fill port and pump up to shut off the fuel fill hose.

I use the same type of barrel for my 30hp - only cut down the top so it would still be high enough to cover the cavitation plate. Lower outboard into water ensuring the water level is around 2 inches above the cavitation plate. When the outboard is running normally the engines fuel pumps create a slight vacuum in the fuel hose.

All drive-in tanks are equipped with a winch to pull the boat up tight against the tank. Atmospheric pressure in the tank through the vent pushes the fuel from the tank to the engine. The ALL ALUMINUM construction includes the motor mount.

Internal baffles virtually eliminate cavitation. Clean out the gas can of old gas and oil mixture because it may be water contaminated. Simply mount it to a sturdy platform place a big bucket underneath it and fill it with water so the propeller is fully submerged.

Testing or troubleshooting an outboard can be a daunting task if youre forced to put the boat on the water each and every time you want to fire up the outbo. If playback doesnt begin shortly try restarting your device. A quick tutorial on how to make a test prop to use in a home made test tank for tweaking idletimingwot at home.

367 3 votes Free Outboard Motor Test Tank plans - See how it was done in the old days before we had the ear muffs that go on the motor. In this case the check valves are both slightly open and allowing fuel flow at the rate that the engine is using it. Remove the fuel hose from the pickup tube fitting and install the low-pressure air pressure gauge and hose.

Then put your motor on a motor stand or the back of your boat. These hydro-engineered test tanks are designed for outboard motors. The tanks can be used with both IO and outboard motors.

See my other videos for the test prop. They are usually happy to give them away to get rid of them. The 1600-H may be used on this test tank.

Creating a homemade test tank may be the best solution. 50 out of 5 stars. 1600 Outboard Test Tank is for the larger shop This tank will accommodate three outboards.

This 5 x 5 tank has a 520 gallon water capacity. Back boat up to drum or tank. An outboard motor test tank having a top a side and a bottom said top being provided with an exhaust fume vent near one end of the tank and an opening nearer the other end of the tank to admit the lower unit of a motor to be tested said top being provided with a transom at one side of the opening disposed transversely of the tank and spaced from the last mentioned end for the support of said motor a baffle supported from the sides of the tank at the same end of the tank.

Just a quick video on how to turn a 55gallon plastic barrel into a test tank with a test prop. Use a jigsaw to cut enough of the top of the barrel away to allow the foot to fit inside the barrel. The air hydraulic lift arm also.

As an example we have tested a 15 hp motor full throttle in. If you need a motor test tank than we have one for you. Compression-testing a cold engine wont give accurate results so the engine has to be warmed up to.

Rated up to V-6 this tank will accommodate 20 and 25 shafts. Make a test tank for large outboards cheap. These tanks are designed to be used with standard propellers eliminating the need for costly test wheels.

Pump up the tank with air but Do Not Exceed 3 lbs of pressure. Go onto to Bossweb and you may be surprised what comes up or PM someone like Seahorse he may have a copy with the amount of years he has been working on outboards. An Air Hydraulic Boom for lifting outboard motors into the tank is available for the Drive-In Tanks with transom boards.

The standard DT-T-TB tank is equipped with a removable transom board for testing loose outboard motors. You can test an outboard motor without access to a boat or ocean. Test Tank for your Outboard - YouTube.

Call or email for pricing. Rebuild Service For Yamaha outboard 60 70 75 85 90HP 3 Ram trim tilt unit 6H1-10. Check out this free plan.

To use rotate the motor up into the lock position roll the stand into the test tank brackets and pin them into place then rotate the outboard back down into the run position while on the stand. Left the motor into the test tank is made easy by the hydraulic lift arm. Best regards for 39 degree Celsius days here in Sydney.

No Test Wheels Needed. Videos you watch may be added to the TVs watch. Theyre easy to make Bunnings wheelie bins make great test tanks and theyll save you wasting litres of water every time you want to flush your engine.

A compression test by the way measures how much each piston is compressing the air in the cylinder using a simple gauge threaded into the spark plug port. You would need test wheels with either though to keep water in them when opening the throttle.

Mercury Outboard Low Oil Alarm Switch Repair Youtube Mercury Outboard Outboard Repair

Bagikan Artikel ini